GWJ Company

contactshipcallwe ship worldwide

Shopping Cart  [more]

Your cart is empty.

Shop by Manufacturer

Index of Products

LMC Premium Metal Impression Jackets

LMC Premium Metal Impression Jackets

About LMC Jackets


PREMIUM COATING
These robust steel jackets are topped with a 'Liquid Metal Coating' (LMC) on ceramic base for optimum ink repellency and durability.

EXTENSIVE SPEC
A complete range of tolerances are available to meet the requirements and specifications of almost every perfecting press make and model.

EXTREME DURABILITY
Registered LMC Jackets are guaranteed for 36 million impressions. This is supported by a high resistance to solvents and heat (up to 700°C).

IMPRESSION JACKET MAINTENACE

MAINTENANCE
To ensure optimum performance please clean LMC Jackets manually with a suitable wash at least once per shift. Then wipe clean with a damp non abrasive cloth. Avoid using excessive pressure and do not use any kind of tool (e.g. metal or plastic ink knife). Such action may damage the surface and performance of the LMC Jacket. Manual cleaning may be required in addition to any auto wash system.

CLEANING
Use only Fogra approved chemical solutions. If other chemical solutions are to be used on LMC Jackets then ensure that they have a flash point above 55ºC and contain no acetone. In addition they should contain less than 1% aromatic compounds and contain no solid particles. Chemical solutions should have a pH value between 5.0 to 9.0 Ink should never be allowed to dry on to the surface of the jacket.

INSTALLATION
Only use approved engineers to install LMC Jackets.

TRANSFER JACKET MAINTENACE

MAINTENANCE
Maintenance tips. To maintain the specific repellent qualities of the transfer jackets it is vital to clean correctly and remove all ink residues. Clean manually with a suitable wash at least once per shift. Then wipe clean with a damp non abrasive cloth. Avoid using excessive pressure and do not use any kind of tool (e.g. metal or plastic ink knife). Such action may damage the surface & performance of the micro grain jacket.

CLEANING
Use only water miscible solutions. Do not use general aggressive chemical solutions (e.g. Ink Stripper or Meter Roller Cleaner). Ink should never be allowed to dry on to the surface of the jacket.

INSTALLATION
Transfer Jackets should only be installed by a competent engineer. Please note that the textured surface of the jacket will change over time.

Heidelberg

Shinoda Part No. Model Thickness Base Steel Substrate Manufacturers Part No. Notes
LMC-HA255 SM102 0.251-0.255 0.22 S8.581.184.N
LMC-HA260 SM102 0.256-0.260 0.22 S8.581.185.N
LMC-HA265 SM102 0.261-0.265 0.22 S8.581.186.N
LMC-HA270 SM102 0.265-0.270 0.22 S8.581.187.N
LMC-HA290 SM102 0.285-0.290 0.25 S9.581.183.N
LMC-HA300 SM102/SX102 0.296-0.300 0.25 S9.581.184.N TC.581.184.N
LMC-HA305 SM102/SX102 0.301-0.305 0.25 S9.581.185.N TC.581.185.N
LMC-HA310 SM102/SX102 0.306-0.310 0.25 S9.581.186.N TC.581.186.N
LMC-HA315 SM102/SX102 0.311-0.315 0.25 S9.581.187.N TC.581.187.N
LMC-HA340 SM102 0.320-0.340 0.25 SA.581.183.N
LMC-H74-300 SM74/SX74 0.296-0.300 0.25 M2.581.184.N
LMC-H74-305 SM74/SX74 0.301-0.305 0.25 M2.581.185.N
LMC-H74-310 SM74/SX74 0.306-0.310 0.25 M2.581.186.N
LMC-H74-315 SM74/SX74 0.311-0.315 0.25 M2.581.187.N
LMC-H52-300 SM52/SX52 0.296-0.300 0.25 G2.581.184.N
LMC-H52-305 SM52/SX52 0.301-0.305 0.25 G2.581.185.N
LMC-H52-310 SM52/SX52 0.306-0.310 0.25 G2.581.186.N
LMC-H52-315 SM52/SX52 0.311-0.315 0.25 G2.581.187.N
LMC-HXE300 XL106 0.296-0.300 0.25 F4.581.184.N
LMC-HXE305 XL106 0.301-0.305 0.25 F4.581.185.N
LMC-HXE310 XL106 0.306-0.310 0.25 F4.581.186.N
LMC-HXE315 XL106 0.311-0.315 0.25 F4.581.187.N
LMC-HX300 XL105 0.296-0.300 0.25 F2.581.184.N
LMC-HX305 XL105 0.301-0.305 0.25 F2.581.185.N
LMC-HX310 XL105 0.306-0.310 0.25 F2.581.186.N
LMC-HX315 XL105 0.311-0.315 0.25 F2.581.187.N
LMC-HX75-300 XL75/CD74 0.296-0.300 0.25 L2.581.184.N
LMC-HX75-305 XL75/CD74 0.301-0.305 0.25 L2.581.185.N
LMC-HX75-310 XL75/CD74 0.306-0.310 0.25 L2.581.186.N
LMC-HX75-315 XL75/CD74 0.311-0.315 0.25 L2.581.187.N

Komori

Shinoda Part No. Model Thickness Base Steel Substrate Manufacturers Part No. Notes
LMC-KAT2K L40SP 0.411-0.420 0.30 742.3202.401 Upper
LMC-KAB2 L40SP 0.411-0.420 0.30 742.3251.301 Lower
LMC-KAT-700-3 L40SP 0.300 0.30 742.3202.500 Plain Steel
LMC-KATK L40SP 0.411-0.420 0.35 742.3202.403 Upper
LMC-KAB L40SP 0.411-0.420 0.35 742.3251.303 Lower
LMC-KAT-700 L40SP 0.350 0.35 742.3202.500 Plain Steel
LMC-KSATK LS40SP 0.411-0.420 0.35 GFH.3200.201 Upper
LMC-KSAB LS40SP 0.411-0.420 0.35 714.3250.600 Lower
LMC-KSAT-700 LS40SP 0.350 0.35 714.3200.800 Plain Steel
LMC-KATK L40P 0.411-0.420 0.30 IGS.3234.112 10 Holes
LMC-KAXX L40P 0.300 0.30 IGS.3234.022 Etch Lined
LMC-KSATK LS40P 0.411-0.420 0.35 GFH.3200.201 10 Holes
LMC-KSATK G40P/GL40P 0.411-0.420 0.35 GFH.3200.201 10 Holes
LMC-K26P L26P 0.365-0.370 0.30 SFU.3305.202
LMC-K26P-700 L26P 0.300 0.30 SFU.3202.200 Plain Steel
LMC-K28P L28P 0.365-0.370 0.30 SFV.3303.200
LMC-K28PXX L28P 0.300 0.30 SFV.3202.201 Etch Lined
LMC-KLS29P LS29P 0.360-0.380 0.30 834.3200.301 52mm Pitch, Width 760mm
LMC-KLS29PP LS29P 0.360-0.380 0.30 834.3200.401 50mm Pitch, Width 750mm
LMC-K29P SPICA 29 0.411-0.420 0.35 345.3500.803

Akiyama

Shinoda Part No. Model Thickness Base Steel Substrate Manufacturers Part No. Notes
LMC-AAAII JP40 0.365-0.370 0.30

KBA

Shinoda Part No. Model Thickness Base Steel Substrate Manufacturers Part No. Notes
LMC-KBA05 Rapida 105 0.300-0.305 0.25
LMC-KBA06 Rapida 106 0.300-0.305 0.25 P7008960

Mitsubishi

Shinoda Part No. Model Thickness Base Steel Substrate Manufacturers Part No. Notes
LMC-MATP-A TP D3000 0.306-0.315 0.25 Width 1045mm
LMC-MATP-B TP D3000 0.306-0.315 0.25 Width 1055mm

ManRoland

Shinoda Part No. Model Thickness Base Steel Substrate Manufacturers Part No. Notes
LMC-RA701 700 0.301-0.305 0.25

Ryobi

Shinoda Part No. Model Thickness Base Steel Substrate Manufacturers Part No. Notes
LMC-RB520 520 0.310-0.320 0.25 5554-23-353
LMC-RB750 750 0.310-0.320 0.25 5747-23-528
LMC-RB780 780 0.310-0.320 0.25 5797-23-528X
LMC-RB920 920 0.310-0.320 0.25 5897-23-529
LMC-RBA 1050 0.310-0.320 0.25 5057-23-528X

Shinohara

Shinoda Part No. Model Thickness Base Steel Substrate Manufacturers Part No. Notes
LMC-SH52 52 0.301-0.305 0.25
LMC-SH66 66 0.311-0.315 0.25
LMC-SH75 75 0.311-0.315 0.25

Freight will be charged according to product

LMC Jackets must be installed by an approved engineer.
Sold on a pre-paid basis.

  • Manufactured by: Shinoda

Please Choose:
Check the box for the product, then add to the cart.

LMC Premium Metal Impression Jackets




































































Add to Cart:
Copyright © 2024 GWJ Co. All rights reserved.
Other products and companies referred to herein are trademarks or registered trademarks of their respective companies.
**Prices, images and specifications subject to change without notice.**

PIA Member    D & B Verified

For your convenience, we accept these credit cards:
Credit Card Logos